Tank Volume Calculator – LSI Industry
SIMULATION · Indicative estimate – not valid for legal metrological calibration, tax or contractual purposes. Theoretical geometric volume, not temperature-corrected.
Geometry example data
My tanks saved in this browser
Volume at level
Geometric volume at the liquid temperature, with no correction applied. Values are rounded for readability. US gal = US liquid gallon (3.785 L).
Level for a volume
The reverse calculation: enter the volume you want to load or have in stock and the calculator shows how high the liquid reaches.
Level → volume table simulated
| Level () | Volume (L) | Volume (m³) | Volume (US gal) | Fill |
|---|
User guide
The calculator is designed for people who already know tanks and want a quick, repeatable estimate. Below you will find what it calculates, the limits of a geometric estimate and a few tips for getting sensible figures.
What it does and what it cannot do
What it does
- Calculates the volume of an ideal geometric shape from the internal dimensions you enter.
- Returns the volume at a given level, the total capacity, the ullage (free space) and the change in volume per unit of level.
- Builds a level → volume table with the step you choose and finds the level that corresponds to a volume.
- Flags unusual combinations of dimensions, which often point to a unit or measurement error.
What it cannot do
- It does not know your actual tank: ovality, deformation, settlement, tilt, internal fittings (manholes, pipes, stiffeners), sediment and water bottoms are not taken into account.
- It applies no temperature or density correction: the volume is the one at the liquid temperature.
- It does not replace a tank calibration carried out to standards (e.g. ISO 7507, API MPMS Chapter 2) and has no value for excise, tax documents or contracts.
- It does not check your measurements: the result is only as accurate as the data you enter.
How to take the measurements
- Always use internal dimensions. Subtract twice the shell thickness from the external diameter. On a 2,500 mm tank, ignoring 6 mm of wall thickness is worth about 1% of the volume.
- Level: the height of the liquid above the lowest internal point, i.e. what a dipstick resting on the bottom would read.
- Horizontal cylinder: enter the length of the cylindrical shell only, between the welds of the two heads. Head depth is measured from the weld to the crown.
- Vertical cylinder: the height is that of the cylindrical shell only; bottom and roof are added with their own depth.
- Tilt: on a 6 m (20 ft) horizontal tank, a 1% slope shifts the level by 60 mm (2.4 in) between the two ends. In that case, measure the level at the middle of the tank.
Available geometries
- Horizontal cylinder with flat, 2:1 elliptical (depth equal to a quarter of the diameter), custom-depth elliptical or hemispherical heads.
- Vertical cylinder with flat, conical, elliptical or hemispherical bottom and roof, chosen independently.
- Sphere and rectangular tank.
- Torispherical heads (ASME F&D, Klöpper, Korbbogen) are well approximated by an elliptical head of the same actual depth. The difference remains small on the total volume but can matter more at very low levels.
How to read the results
Change per mm (or per inch with imperial units) shows how many litres correspond to one unit of level at that point. It tells you how much a reading error weighs: it is highest at mid-height of a horizontal tank and lowest near the bottom and the top.
Copy for Excel copies the table with tab separators and decimal points, ready to paste into a spreadsheet. The copied table starts with the notice about the indicative nature of the values.
My tanks stays only in the browser you are using: no data is sent to LSI or to third parties.
How the calculation is verified
Each shape uses closed-form geometric formulas. The formulas are checked against a second, independent method, numerical integration of the tank in thin slices, on nine test geometries and one hundred levels each. The largest deviation is below 0.0001% of capacity, negligible compared with any field measurement uncertainty.
The calculator version and date are shown at the bottom of the page and on every exported table.